Motorola M68CPU32BUG Manual do Utilizador Página 95
- Página / 196
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
DEBUG MONITOR COMMANDS
M68CPU32BUG/D REV 1 3-65
TM Transparent Mode TM
3.32 TRANSPARENT MODE
TM [<port>][<escape>]
The TM command connects the console serial port and the host port together, allowing the user
to communicate with a host computer. A message displayed by TM shows the current escape
character, i.e., the character used to exit the transparent mode. The two ports remain connected
until the escape character is received by the console port. The escape character is not transmitted
to the host and at power up or reset is initialized to $01=^A.
The optional port number allows the user to specify which port is the host port. If the port
number is omitted the default is port 1. The port number must be within the range 0 to $1F.
Ports do not have to have the same baud rate, but for reliable operation the terminal port baud
rate should be equal to or greater than the host port baud rate. Use the PF command to change
baud rates.
The optional escape argument allows the user to specify the exit character. Use one of three
formats:
ascii code : $03 Set escape character to ^C
ascii character : ’c Set escape character to c
control character : ^C Set escape character to ^C
If the port number is omitted and the escape argument is entered as a numeric value, precede the
escape argument with a comma to distinguish it from a port number.
EXAMPLES
CPU32Bug>TM<CR>
Enter TM.
Escape character: $01=^ A
Exit code is always displayed.
<^A>
Exit transparent mode.
CPU32Bug>TM ^g<CR> Enter TM and set escape character
Escape character: $07=^ G to ^ G.
<^G> Exit transparent mode.
CPU32Bug>
- M68CPU32BUG DEBUG MONITOR 1
- USER’S MANUAL 1
- M68CPU32BUG/D 1
- TABLE OF CONTENTS 3
- M68CPU32BUG/D REV 1 ii 4
- M68CPU32BUG/D REV 1 iii 5
- M68CPU32BUG/D REV 1 iv 6
- M68CPU32BUG/D REV 1 v 7
- LIST OF FIGURES 8
- LIST OF TABLES 8
- CHAPTER 1 9
- 1.1 INTRODUCTION 9
- 1.2 GENERAL DESCRIPTION 9
- GENERAL INFORMATION 10
- M68CPU32BUG/D REV 1 1-2 10
- 1.3 USING THIS MANUAL 11
- 1.5 SYSTEM RESTART 12
- 1.6 MEMORY REQUIREMENTS 13
- Figure 1-2. BCC Memory Map 14
- M68CPU32BUG/D REV 1 1-7 15
- M68CPU32BUG/D REV 1 1-8 16
- CHAPTER 2 17
- DEBUG MONITOR DESCRIPTION 17
- 2.1 INTRODUCTION 17
- M68CPU32BUG/D REV 1 2-2 18
- M68CPU32BUG/D REV 1 2-3 19
- M68CPU32BUG/D REV 1 2-4 20
- M68CPU32BUG/D REV 1 2-5 21
- M68CPU32BUG/D REV 1 2-6 22
- M68CPU32BUG/D REV 1 2-7 23
- M68CPU32BUG/D REV 1 2-8 24
- M68CPU32BUG/D REV 1 2-9 25
- M68CPU32BUG/D REV 1 2-10 26
- M68CPU32BUG/D REV 1 2-11 27
- 2.6 FUNCTION CODE SUPPORT 28
- M68CPU32BUG/D REV 1 2-13 29
- M68CPU32BUG/D REV 1 2-14 30
- CHAPTER 3 31
- 3.1 INTRODUCTION 31
- M68CPU32BUG/D REV 1 3-2 32
- BC Block of Memory Compare BC 33
- BF Block of Memory Fill BF 35
- BM Block of Memory Move BM 37
- BR Breakpoint Insert BR 39
- BS Block of Memory Search BS 40
- BV Block of Memory Verify BV 43
- DC Data Conversion DC 45
- DU Dump S-Records DU 46
- M68CPU32BUG/D REV 1 3-19 49
- M68CPU32BUG/D REV 1 3-20 50
- GN Go To Next Instruction GN 51
- GO Go Execute User Program GO 53
- M68CPU32BUG/D REV 1 3-26 56
- M68CPU32BUG/D REV 1 3-27 57
- HE Help HE 58
- M68CPU32BUG/D REV 1 3-31 61
- M68CPU32BUG/D REV 1 3-32 62
- M68CPU32BUG/D REV 1 3-33 63
- MA Macro Define/Display MA 64
- MAE Macro Edit MAE 67
- M68CPU32BUG/D REV 1 3-39 69
- MD Memory Display MD 70
- MM Memory Modify MM 72
- MS Memory Set MS 74
- M68CPU32BUG/D REV 1 3-45 75
- M68CPU32BUG/D REV 1 3-46 76
- M68CPU32BUG/D REV 1 3-47 77
- PA Printer Attached PA 78
- PF Port Format PF 79
- RD Register Display RD 82
- RESET Cold/Warm Reset RESET 86
- RM Register Modify RM 87
- RS Register Set RS 88
- SD Switch Directories SD 89
- T Trace T 90
- M68CPU32BUG/D REV 1 3-63 93
- Trace on change of flow: 94
- TM Transparent Mode TM 95
- M68CPU32BUG/D REV 1 3-66 96
- M68CPU32BUG/D REV 1 3-67 97
- M68CPU32BUG/D REV 1 3-68 98
- M68CPU32BUG/D REV 1 3-69 99
- DEBUG MONITOR COMMANDS 100
- M68CPU32BUG/D REV 1 3-70 100
- M68CPU32BUG/D REV 1 3-71 101
- M68CPU32BUG/D REV 1 3-72 102
- CHAPTER 4 103
- ASSEMBLER/DISASSEMBLER 103
- 4.1 INTRODUCTION 103
- 4.2SOURCE PROGRAM CODING 104
- M68CPU32BUG/D 4-3 105
- M68CPU32BUG/D 4-4 106
- Pseudo Registers 107
- Main Processor Registers 107
- M68CPU32BUG/D 4-6 108
- M68CPU32BUG/D 4-7 109
- M68CPU32BUG/D 4-8 110
- M68CPU32BUG/D 4-9 111
- M68CPU32BUG/D 4-10 112
- M68CPU32BUG/D 4-11 113
- 0000D000 6000BF68 BRA *-4096 114
- 0000D000 60FE BRA.B * 114
- 0000D000 4EF90000 D000 JMP * 114
- CHAPTER 5 115
- SYSTEM CALLS 115
- 5.1 INTRODUCTION 115
- 5.2 SYSTEM CALL ROUTINES 116
- M68CPU32BUG/D REV 1 5-3 117
- M68CPU32BUG/D REV 1 5-4 118
- M68CPU32BUG/D REV 1 5-5 119
- COUNT = 3 120
- COUNT = 3? 5<CR> 120
- COUNT = 5 120
- COUNT = 3? <CR> 120
- SYSCALL .CHKBRK 121
- BEQ BREAK 121
- M68CPU32BUG/D REV 1 5-8 122
- M68CPU32BUG/D REV 1 5-9 123
- .ERASLN Erase Line .ERASLN 124
- SYSCALL .INCHR Call .INCHR 125
- M68CPU32BUG/D REV 1 5-12 126
- M68CPU32BUG/D REV 1 5-13 127
- M68CPU32BUG/D REV 1 5-14 128
- MOVE.B D0,-(A7) 129
- Send character in D0 129
- SYSCALL .OUTCHR 129
- To default output port 129
- .OUTSTR .OUTSTR 130
- M68CPU32BUG/D REV 1 5-17 131
- PEA (A0) 132
- Long buffer address 132
- SYSCALL .READLN 132
- M68CPU32BUG/D REV 1 5-19 133
- SYSCALL .RETURN 134
- Return to CPU32Bug 134
- .SNDBRK Send Break .SNDBRK 135
- M68CPU32BUG/D REV 1 5-22 136
- SYSCALL .TM_INI 137
- Initialize timer 137
- .TM_RD Read Timer .TM_RD 138
- SYSCALL .TM_STR0 139
- Start Timer at T=0 .TM_STR0 140
- .WRITDLN .WRITDLN 141
- .WRITELN .WRITELN 143
- CHAPTER 6 145
- DIAGNOSTIC FIRMWARE GUIDE 145
- 6.1 INTRODUCTION 145
- 6.2 DIAGNOSTIC MONITOR 145
- M68CPU32BUG/D REV 1 6-2 146
- M68CPU32BUG/D REV 1 6-3 147
- 6.3 UTILITIES 148
- M68CPU32BUG/D REV 1 6-5 149
- CPU CPU Tests For The MCU CPU 150
- CPU A Register Test CPU A 151
- CPU B Instruction Test CPU B 152
- CPU C Address Mode Test CPU C 153
- M68CPU32BUG/D REV 1 6-10 154
- MT Memory Tests MT 155
- M68CPU32BUG/D REV 1 6-12 156
- MT A Set Function Code MT A 157
- MT B Set Start Address MT B 158
- MT C Set Stop Address MT C 159
- MT D Set Bus Data Width MT D 160
- MT E March Address Test MT E 161
- MT F Walk a Bit Test MT F 162
- MT G Refresh Test MT G 163
- MT H Random Byte Test MT H 164
- MT I Program Test MT I 165
- MT J Test and Set Test MT J 166
- BERR Bus Error Test BERR 167
- M68CPU32BUG/D REV 1 6-24 168
- APPENDIX A 169
- S-RECORD INFORMATION 169
- A.1 INTRODUCTION 169
- A.2 S-RECORD CONTENT 169
- A.3 S-RECORD TYPES 170
- A.4 S-RECORDS CREATION 171
- M68CPU32BUG REV 1 A-4 172
- APPENDIX B 173
- SELF-TEST ERROR MESSAGES 173
- B.1 INTRODUCTION 173
- M68CPU32BUG REV 1 B-2 174
- APPENDIX C 175
- USER CUSTOMIZATION 175
- C.1 INTRODUCTION 175
- C.2 CPU32BUG CUSTOMIZATION 176
- M68CPU32BUG REV 1 C-3 177
- C>DEL TMP.MX<CR> 178
- C>DEL C32B1.MX<CR> 178
- C.3 CUSTOMIZATION TABLE 179
- M68CPU32BUG REV 1 C-6 180
- M68CPU32BUG REV 1 C-7 181
- ROM AUTO BOOT VECTORS 182
- Periodic Interrupt Timer 183
- M68CPU32BUG REV 1 C-10 184
- M68CPU32BUG REV 1 C-11 185
- M68CPU32BUG REV 1 C-12 186
- M68CPU32BUG REV 1 C-13 187
- C.4 COMMUNICATION FORMATS 188
- M68CPU32BUG REV 1 C-15 189
- M68CPU32BUG REV 1 C-16 190
- Platform Board 191
- M68CPU32BUG REV 1 C-18 192
- Offset Value Comment 193
- M68CPU32BUG REV 1 C-20 194
- M68CPU32BUG REV 1 C-21 195
- M68CPU32BUG REV 1 C-22 196
Manuais e produtos relacionados com TVs e monitores Motorola M68CPU32BUG
TVs e monitores Motorola V60 Guia do Utilizador
(120 páginas)
(120 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 2.495 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais