Motorola Symbol LS4278 Especificações descarregar pdf (Página 2)

5 6 74

Cradle Parts

Cradle Connections

Important: Connect the interface cable and

power supply (if necessary) in the following

order to ensure proper operation of the

scanner and cradle:

1. Insert the interface cable into the cradle’s

host port.

2. Connect the other end of the interface

cable to the host, if needed.

3. If necessary, connect the power supply to

the cradle’s power port (if required by the

interface, or to allow fast charging of the

scanner).

4. Connect the appropriate cable to the

power supply and an AC power source, if

necessary.

5. If applicable, thread the interface cable

over the cable support hook and run the

host and power cables into their

respective cable grooves.

6. If necessary, scan the appropriate host

bar code (for non-autodetected

interfaces). Refer to the Product

Reference Guide.

Changing the Host Interface

To connect to a different host, or to the same host through a different cable:

1. Unplug the power supply from the cradle.

2. Unplug the interface cable from the host.

3. Connect the interface cable to the new host, or the new interface cable to the

existing host.

4. Reconnect the power supply, if required.

5. If necessary, scan the appropriate host bar code (for non-autodetected interfaces).

Refer to the Product Reference Guide.

If the scanner does not recognize the host, disconnect the power supply,

then reconnect after connecting the host cable.

Mounting the Cradle

Horizontal Mount

1. Ensure the desk/wall mount

converter knob is in the correct

position, shown at right.

2. If mounting the cradle

horizontally where no fastening

is necessary, ensure the rubber

feet are attached to the cradle.

These feet provide traction and

prevent surface damage.

Vertical Mount

To mount the cradle on a vertical surface:

1. Use a Philips screwdriver to turn the desk/

wall mount converter knob to the position

shown at right. The front latches protract to

engage the depressions at the base of the

scanner’s handle.

2. Ensure the convertable mount hook on the

front of the cradle is inserted with the hook

facing up. If not, remove and reverse the

hook so that it is in position to secure the

scanner in place.

3. Attach the interface and power cables to the

appropriate ports (see Cradle Connections).

4. Position the mounting template on the

mounting surface.

5. Using the screw hole notations on the wall

mount template, mark the surface to

determine the location of the screw holes.

6. Pre-drill holes to accommodate six #8 Pan

head screws, 5/8" in length.

7. Screw the bracket onto the surface ensuring

that the front and bottom screws are

screwed against the height tabs (see Wall Mount Template).

8. Press the cables into the cradle cable grooves.

9. Align the cradle mounting holes with the screws on the mounting surface and snap

the cradle securely into place on the surface.

10.Place the scanner in the cradle.

Inserting the Scanner in the Cradle

To insert the scanner in the cradle:

1. Insert the scanner top first. When the cradle is mounted in a vertical position, ensure

the convertable mount hook on the front of the cradle is inserted with the hook facing

up. If not, remove and reverse the hook so that it is in position to secure the scanner

in place.

2. Push the handle until it clicks into place, engaging the contacts in the cradle and

scanner.

Sending Data to the Host Computer

The cradle receives data from the scanner via a wireless radio connection and transmits

it to the host computer via the host cable. The scanner and cradle must be paired for

successful wireless communication.

Pairing

Pairing registers a scanner to the cradle and the scanner and cradle can exchange

information. The STB4278 operates in two mode: scanner-to-cradle and multi scanner-

to-cradle. In scanner-to-cradle mode, the scanner is paired to the cradle either by

insertion into the cradle (if pairing on insertion is enabled), or by scanning the pairing bar

code. In multi scanner-to-cradle mode, up to three scanners can be paired to one

cradle. A multipoint bar code must be scanned to activate this feature.

The cradle includes pairing bar codes on both its front and back. To pair the scanner

with the cradle, scan a pairing bar code. A high-low-high-low beep sequence followed

by a low-high beep sequence indicates successful pairing and connection to the remote

device. A long low, long high beep sequence indicates unsuccessful pairing. Refer to

the Product Reference Guide for more information.

Lost Connection to Host

If scanned data does not transmit to the cradle’s host, ensure that all cables are firmly

inserted and the power supply is connected to an appropriate AC outlet. If scanned data

still does not transmit to the host, reestablish a connection with the host:

1. Disconnect the power supply from the cradle.

2. Disconnect the host interface cable from the cradle.

3. Wait three seconds.

4. Reconnect the host interface cable to the cradle.

5. Reconnect the power supply to the cradle, if required.

6. Reestablish pairing with the cradle by scanning the pairing bar code.

Charging the Scanner Battery in the Cradle

To charge the scanner battery, place the scanner in the cradle (see Inserting the

Scanner in the Cradle). The battery begins charging when the scanner LED indicator

starts flashing green. A complete charge of a fully discharged battery can take up to

three hours using external power and up to five hours using non-external cable power.

LED Charging Indications

When powered up, the cradle LED is always green. Refer to the LS4278 Quick

Reference Guide for scanner LED indications.

Using a Host Interface to Supply Power

Some hosts can provide power to the cradle via the host interface, instead of an

external power supply.

Troubleshooting

If the cradle does not work after following the previous procedures:

•

Check the system power.

•

Check for loose cable connections.

•

Check that the scanner is inserted properly in the cradle.

•

Check that the host settings are correct and the cradle is connected to the appropriate

port on the host.

Wall Mount Template

Rubber

Foot

Rubber

Foot

Rubber

Foot

Rubber

Foot

Host

Cable

Groove

Mounting

Hole

Cable

Support

Hooks

Power

Port

Host

Port

Power

Cable

Groove

Desk/Wall Mount

Converter Knob

Mounting

Hole

Pairing Bar

Code

Latches

Charging/

Communication

Contacts

Front

Back

Convertable

Mount Hook

Power Port

Host

Port

NOTE For your convenience, a mounting bracket can be purchased from

Motorola. For the appropriate measurements, use the wall mount

template included in this guide.

Converter Knob:

Horizontal Mount Position

Converter Knob:

Vertical Mount Position

NOTE The STB4278 does not always require a power supply whereas the

STB4208 always requires a power supply.

CAUTION Do not pour, spray, or spill any liquid on the cradle.

Dimension Tolerance = ± .02 in (± .5 mm)

Height Tab

Screw Holes

Height Tab

1 2

Comentários a estes Manuais

Sem comentários

Motorola Symbol LS4278 Especificações Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Leitores de códigos de barras Motorola Symbol LS4278