Motorola CPCI-6115 Manual de Serviço Página 40
- Página / 196
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Hardware Preparation and Installation
CPCI-6200 Installation and Use (6806800J66C)
40
5. Remove the filler panel from the appropriate card slot.
6. Set the VIO on the backplane to either +3.3 V or +5 V, depending on your
CompactPCI system signaling requirements, and ensure the backplane does not
bus J3 or J5 signals.
7. Slide the baseboard into the appropriate slot.
Grasping the top and bottom injector handles, be sure the module is well seated in
the P1 through P5 connectors on the backplane. Make sure you do not damage or
bend connector pins.
8. Secure the baseboard in the chassis with the screws provided, making good
contact with the transverse mounting rails to minimize RF emissions.
9. Replace the chassis or system cover(s), and make sure no cables are pinched.
10.Cable the peripherals to the panel connectors, and then reconnect the system to
the AC or DC power source.
11.Turn the equipment power on.
After you have verified that all necessary hardware preparation has been done, that all
connections have been made correctly and that the installation is complete, you can power up
the system. The MPU, hardware and firmware initialization process is performed by the
MOTLoad power-up or system reset. The firmware initializes the devices on the baseboard in
preparation for booting the operating system.
The firmware is shipped from the factory with an appropriate set of defaults. In most cases
there is no need to modify the firmware configuration before you boot the operating system.
For more information on MOTLoad, see MOTLoad Firmware on page 95.
- CPCI-6200 1
- Trademarks 2
- Contact Address 2
- Contents 3
- List of Tables 10
- List of Figures 13
- About this Manual 15
- Conventions 18
- Summary of Changes 19
- Introduction 21
- 1.2 Standard Compliances 24
- 1.3 Mechanical Data 26
- 1.4 Ordering Information 26
- 1.5 Product Identification 27
- Chapter 2 29
- 2.1 Overview 29
- 2.4 Power Requirements 31
- 2.5 Installing Accessories 32
- PMC Filler Plate 33
- PMC Alignment 33
- Voltage Key 33
- 2.6.3 Hardware Configuration 35
- 2.10 Factory-Installed Linux 42
- Chapter 3 45
- 3.1 Board Layout 45
- 3.2 Front Panel 46
- 3.3 Connectors and Headers 47
- 3.3.1 CPCI Bus Connector, J1 48
- 3.3.2 CPCI Bus Connector, J2 49
- 3.3.4 CPCI Connector, J4 51
- 3.3.7 Ethernet Connector 58
- 3.3.8 USB Connector 58
- 3.4 Switches 66
- 3.5 Front Panel LEDs 67
- 3.6 Status Indicators 68
- Functional Description 71
- 4.4 System Memory 74
- 4.5 Timers 75
- 4.6 Ethernet Interfaces 75
- 4.7 Local Bus Interface 75
- 4.7.3 Control and Timers PLD 77
- 4.8 DUART Interface 78
- 4.9 PCI Express Port 79
- 4.10 PCI/PCI-X Bus 80
- 4.11 Operation Modes 81
- 4.11.1 System Controller Mode 82
- 4.11.2 Peripheral Mode 82
- 4.11.3 Stand Alone Mode 83
- 4.12 PCI Express Expansion 84
- 4.13 System Interrupts 85
- 4.14 Clock Distribution 86
- 4.15 MPC8572 System Clock 87
- 4.16 Reset Control Logic 87
- 4.16.1 Abort/Reset Switch 89
- 4.16.2 Reset Timing 90
- 4.17 RTC Battery 91
- 4.18 IPMI Controller 91
- 4.19 Programmable Devices 93
- 4.19.1 Local Bus Control CPLD 94
- 4.19.2 Reset CPLD 94
- 4.19.3 CPCI Control CPLD 94
- 5.4 MOTLoad Commands 96
- 5.6 MOTLoad Tests 96
- 5.7 Using MOTLoad 97
- 5.7.2 Command Line Help 99
- 5.7.3 Command Line Rules 99
- 5.8 MOTLoad Command List 100
- MOTLoad Firmware 101
- Control via IPMI 107
- 6.1.3 IPMI Messaging Commands 108
- 6.1.4 SEL Device Commands 108
- 6.1.5 SDR Repository Commands 109
- 6.1.6 FRU Inventory Commands 109
- 6.1.7 Sensor Device Commands 110
- 6.2 PICMG 2.9 Commands 111
- 6.3 Emerson Specific Commands 112
- 6.3.2 OEM Commands 115
- 6.3.2.1 BMC/PM Change Role 116
- 6.4 FRU Information 118
- 6.5 Sensor Description 118
- Memory Maps and Addresses 137
- 7.2 CPCI-6200 Memory Map 138
- 7.4 System I/O Memory Map 140
- 7.4.1 System Status Register 143
- 7.4.2 System Control Register 144
- 7.4.5 Interrupt Register 1 148
- 7.4.6 Interrupt Register 2 149
- 7.4.7 Interrupt Mask Register 150
- 7.4.23 PLD Revision Register 167
- 7.4.24 PLD Date Code Register 168
- 7.4.25 Test Register 1 168
- 7.4.26 Test Register 2 169
- 7.4.27.2 Control Registers 170
- 7.4.27.3 Compare Registers 171
- 7.4.27.4 Counter Registers 172
- 7.5 Interrupt Controller 173
- C Device Addresses 174
- 7.7 PCI/PCI-X Configuration 175
- Replacing the Battery 179
- A.2 Replacing the Battery 180
- Related Documentation 181
- B.3 Related Specifications 183
- Safety Notes 185
- Installation 186
- Operation 187
- Hot Swap 188
- Sicherheitshinweise 189
- System Installation 191
- Batterie 192
- © 2009 Emerson Electric Co 196
Manuais e produtos relacionados com Comutadores de rede Motorola CPCI-6115
Comutadores de rede Motorola CPCI-6115 Manual de Serviço
(174 páginas)
(174 páginas)
Comutadores de rede Motorola WS2000 - Wireless Switch - Network Management Device Especificações
(346 páginas)
(346 páginas)
Comutadores de rede Motorola CPCI-6115 Manual de Serviço
(138 páginas)
(138 páginas)
Comutadores de rede Motorola T1/E1 Especificações
(122 páginas)
(122 páginas)
(31 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 2.554 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais